Selasa, 03 Juli 2012

Access Control List (ACL)

  Screen of Cisco Packet Tracer
EDMONTON

  --- System Configuration Dialog ---
Continue with configuration dialog? [yes/no]: no
Press RETURN to get started!
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname Edmonton
Edmonton(config)#int fa0/0
Edmonton(config-if)#ip add 172.16.10.1 255.255.255.0
Edmonton(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Edmonton(config-if)#exit
Edmonton(config)#int fa1/0
Edmonton(config-if)#ip add 172.16.20.1 255.255.255.0
Edmonton(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
Edmonton(config-if)#exit
Edmonton(config)#int se2/0
Edmonton(config-if)#ip add 172.16.30.1 255.255.255.0
Edmonton(config-if)#no shut
%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Edmonton(config-if)#exit
Edmonton(config)#router eigrp 10
Edmonton(config-router)#network 172.16.10.0 0.0.0.255
Edmonton(config-router)#network 172.16.20.0 0.0.0.255
Edmonton(config-router)#network 172.16.30.0 0.0.0.255
Edmonton(config-router)#exit
Edmonton(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Edmonton#
RED DEER
         --- System Configuration Dialog ---
Continue with configuration dialog? [yes/no]: no
Press RETURN to get started!
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname Red_Deer
Red_Deer(config)#int fa0/0
Red_Deer(config-if)#ip add 172.16.40.1 255.255.255.0
Red_Deer(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Red_Deer(config-if)#exit
Red_Deer(config)#int fa1/0
Red_Deer(config-if)#ip add 172.16.50.1 255.255.255.0
Red_Deer(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
Red_Deer(config-if)#exit
Red_Deer(config)#int se2/0
Red_Deer(config-if)#ip add 172.16.30.2 255.255.255.0
Red_Deer(config-if)#clock rate 64000
Red_Deer(config-if)#no shut
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Red_Deer(config-if)#exit
Red_Deer(config)#int se3/0
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up
Red_Deer(config-if)#ip add 172.16.60.1 255.255.255.0
Red_Deer(config-if)#clock rate 64000
Red_Deer(config-if)#no shut
%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Red_Deer(config-if)#exit
Red_Deer(config)#router eigrp 10
Red_Deer(config-router)#network 172.16.40.0 0.0.0.255
Red_Deer(config-router)#network 172.16.50.0 0.0.0.255
Red_Deer(config-router)#network 172.16.30.0 0.0.0.255
Red_Deer(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 172.16.30.1 (Serial2/0) is up: new adjacency
Red_Deer(config-router)#network 172.16.60.0 0.0.0.255
Red_Deer(config-router)#exit
Red_Deer(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Red_Deer#
CALGARY

--- System Configuration Dialog ---
Continue with configuration dialog? [yes/no]: no
Press RETURN to get started!
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#hostname Calgary
Calgary(config)#int fa0/0
Calgary(config-if)#ip add 172.16.70.1 255.255.255.0
Calgary(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Calgary(config-if)#exit
Calgary(config)#int fa1/0
Calgary(config-if)#ip add 172.16.80.1 255.255.255.0
Calgary(config-if)#no shut
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
Calgary(config-if)#exit
Calgary(config)#int se2/0
Calgary(config-if)#ip add 172.16.60.2 255.255.255.0
Calgary(config-if)#no shut
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Calgary(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up
Calgary(config-if)#exit
Calgary(config)#router eigrp 10
Calgary(config-router)#network 172.16.70.0 0.0.0.255
Calgary(config-router)#network 172.16.80.0 0.0.0.255
Calgary(config-router)#network 172.16.60.0 0.0.0.255
Calgary(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 172.16.60.1 (Serial2/0) is up: new adjacency
Calgary(config-router)#exit
Calgary(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Calgary#
 Setting ACL dengan ketentuan sbb:
1. 10.0 tidak boleh di akses oleh 40.0
Edmonton#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Edmonton(config)#access-list 10 deny 172.16.40.0 0.0.0.255
Edmonton(config)#access-list 10 permit any
Edmonton(config)#int fa0/0
Edmonton(config-if)#ip access-group 10 out
Edmonton(config-if)#end
%SYS-5-CONFIG_I: Configured from console by console
Edmonton#
2. 10.7 tidak boleh di akses oleh 10.5
Red_Deer#ena
Red_Deer#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Red_Deer(config)#access-list 110 deny ip host 172.16.10.5 host 172.16.50.7
Red_Deer(config)#access-list 110 permit ip any any
Red_Deer(config)#int fa1/0
Red_Deer(config-if)#ip access-group 110 out
Red_Deer(config-if)#end
%SYS-5-CONFIG_I: Configured from console by console
Red_Deer#
3. 10.5 boleh mengakses Red Deer meggunakan telnet      
  
Red_Deer#ena
Red_Deer#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Red_Deer(config)#access-list 20 permit host 172.16.10.5
Red_Deer(config)#line vty 0 4
Red_Deer(config-line)#access-class 20 in
Red_Deer(config-line)#end
Red_Deer#
%SYS-5-CONFIG_I: Configured from console by console
Diposting oleh di Tidak ada komentar:

Senin, 18 Juni 2012

EIGRP ( Enhanced Interior Gateway Routing Protocol )


Review pada Cisco Packet Tracer

Konfigurasi  PC1 :

IP Address     : 172.16.1.5
Subnet mask  : 255.255.255.0
Gateway        : 172.16.1.1



Konfigurasi  PC2 :

IP Address     : 192.168.2.5
Subnet mask  : 255.255.255.0
Gateway        : 192.168.2.1



Konfigurasi  PC3 :

IP Address     : 192.168.1.5
Subnet mask  : 255.255.255.0
Gateway        : 192.168.1.1



Konfigurasi Router 1 :
 
--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.1.1 255.255.255.0
Router(config-if)#no shutdown
Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 172.16.3.1 255.255.255.252
Router(config-if)#clock rate 64000
Router(config-if)#no shutdown
Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up
exit

Router(config)#int ser 3/0
Router(config-if)#ip add 192.168.10.5 255.255.255.252
Router(config-if)#clock rate 64000
Router(config-if)#no shutdown
Router(config-if)#exit
Router(config)#
%LINK-5-CHANGED: Interface Serial3/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to up
Konfigurasi Router 2 :
 
--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.2.1 255.255.255.0
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
exit
Router(config)#int ser 2/0
Router(config-if)#ip add 172.16.3.2 255.255.255.252
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#exit
Router(config)#int ser3/0
Router(config-if)#ip add 192.168.10.9 255.255.255.252
Router(config-if)#clock rate 64000
Router(config-if)#no shutdown
Router(config-if)#exit
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

%LINK-5-CHANGED: Interface Serial3/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to up
Konfigurasi Router 3 :
 
--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>enable
Router#configure terminal
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

Router(config-if)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
exit
Router(config)#int ser2/0
Router(config-if)#ip add 192.168.10.6 255.255.255.252
Router(config-if)#no shutdown

Router(config-if)#
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
exit
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config)#int ser 3/0
Router(config-if)#ip add 192.168.10.10 255.255.255.252
Router(config-if)#no shutdown

%LINK-5-CHANGED: Interface Serial3/0, changed state to up

Router(config-if)#exit
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to up
Konfigurasi EIGRP pada Router 1 :
 
Router(config)#router eigrp 10
Router(config-router)#network 172.16.1.0 0.0.0.255
Router(config-router)#network 172.16.3.0 0.0.0.3
Router(config-router)#network 192.168.10.4 0.0.0.3
Router(config-router)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console


Konfigurasi EIGRP pada Router 2 :
 

Router(config)#router eigrp 10
Router(config-router)#network 192.168.2.0 0.0.0.255
Router(config-router)#network 172.16.3.0 0.0.0.3
Router(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 172.16.3.1 (Serial2/0) is up: new adjacency
Router(config-router)#network 192.168.10.8 0.0.0.3
Router(config-router)#exit
Router(config)#
%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 192.168.10.10 (Serial3/0) is up: new adjacency



Konfigurasi EIGRP pada Router 3 :
Router(config)#router eigrp 10
Router(config-router)#network 192.168.1.0 0.0.0.255
Router(config-router)#network 192.168.10.4 0.0.0.3
Router(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 192.168.10.5 (Serial2/0) is up: new adjacency
Router(config-router)#network 192.168.10.8 0.0.0.3
Router(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 10: Neighbor 192.168.10.9 (Serial3/0) is up: new adjacency
Router(config-router)#exit
Router(config)#


Diposting oleh di Tidak ada komentar:

Senin, 28 Mei 2012

Reviews Router Statis


Router 1 :
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.3.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 172.16.2.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#exit
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up
Router(config)#
Router(config)#
Router(config)#
Router(config)#conf t
%Invalid hex value
Router(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#ip route 192.168.0.0 255.255.252.0 ser2/0
Router(config)#ip route 172.16.1.0 255.255.255.0 ser2/0
Router(config)#exit

Router 2 :
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 172.16.1.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 172.16.2.2 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to down
Router(config-if)#exit
Router(config)#int ser3/0
Router(config-if)#ip add 192.168.1.2 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial3/0, changed state to down
Router(config-if)#exit
Router(config)#
%LINK-5-CHANGED: Interface Serial2/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up
%LINK-5-CHANGED: Interface Serial3/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial3/0, changed state to up
Router(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#ip route 172.16.3.0 255.255.255.0 ser2/0
Router(config)#ip route 192.168.2.0 255.255.255.0 ser3/0
Router(config)#exit

Router 3 :
Router>ena
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.2.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up
Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#exit
Router(config)#int ser2/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up
Router(config-if)#exit
Router(config)#
Router(config)#ip route 172.16.0.0 255.255.252.0 ser2/0
Router(config)#

Konfigurasi PC

IP PC1 : 172.16.3.2 
SM       : 255.255.255.0
DG       : 172.16.3.1

IP PC2 : 172.16.1.2
SM       : 255.255.255.0
DG       : 172.16.1.1

IP PC3 : 192.168.2.2
SM       : 255.255.255.0
DG       : 192.168.2.1
Diposting oleh di Tidak ada komentar:

Senin, 30 April 2012

Latihan Soal Jaringan Komputer 3

  1.  Berdasarkan pada kondisi yang ditunjukkan oleh gambar, manakah pernyataan berikut yang benar mengenai aliran trafik jaringan pada switch ini?


B. PC yang terkoneksi pada port Fa0/2 dapat berkomunikasi dengan PC lainnya yang terkoneksi pada Port Fa0/22 jika kedua PCs berada pada IP network yang sama. 

  1.  Di jaringan komputer perusahaan besar, mengapa trafik untuk voice biasanya memerlukan VLAN tersendiri?
C. Hal ini untuk memisahkan antara trafik data dengan trafik voice sehingga trafik data tidak akan mempengaruhi trafik voice.

  1. Perhatikan topologi di bawah ini. Administrator jaringan butuh untuk mengkonfigurasikan default route pada router Border. Manakah perintah konfigurasi yang setidaknya paling tepat (mengacu ke router Border) untuk default route yang akan diperlukan oleh router untuk meneruskan paket?
 
A. ip route 0.0.0.0 0.0.0.0 64.100.59.5

  1. Perhatikan gambar berikut. Seorang teknisi jaringan sedang menyelidiki mengapa H1 dan H2 tidak dapat berkomunikasi. Apa masalah yang dapat ditemukan oleh teknisi tersebut?


C. Sw1 membutuhkan sebuah IP address yang berada pada subnet yang sama.
  1.  Manakah pernyataan yang benar yang menjelaskan mengenai fungsi dari VLAN Management Policy Server (VMPS)? 
C.  VMPS melayani backup konfigurasi keanggotaan VLAN secara statis.

  1.  Manakah dua jenis peralatan berikut yang akan mencegah pengiriman data secara broadcast ke seluruh jaringan.? (Pilih dua.)
C. Switch

D. VLAN
  1.  Berdasarkan kondisi di atas, switch – switch saling terkoneksi dengan trunk link dan dikonfigurasikanuntuk VTP. Sebuah VLAN baru ditambahkan ke Switch1. Manakah kejadian berikut yang akan terjadi? (Pilih tiga.)
A. Switch1 tidak akan menambahkan VLAN ke database-nya dan akan meneruskan update    ke Switch2.

B. Switch2 akan menambahkan VLAN ke database-nya dan meneruskan update ke Switch3. 

F. Switch4 tidak akan menerima update.
  1.  Apa yang menjadi tujuan VTP ?
C. Me-rute-kan frame sepanjang jalur terbaik antar switch.
  1. Manakah 3 pernyataan berikut yang benar ketika Router dikonfigurasikan untuk trunking VLAN? 
C. SAtu IP network atau subnetwork untuk tiap subinterface.
E . Sebuah domain manajemen untuk tiap subinterface.
F.  Sebuah enkapsulasi protokol trunking yang kompatibel untuk tiap subinterface.
  1.  Sebuah router memiliki dua interface serial dan dua interface Fast Ethernet. Router ini harus terkoneksi dengan WAN dan sebuah switch yang mendukung untuk empat VLAN. Bagaimana cara mewujudkan kebutuhan ini secara efisien biaya dan efektif untuk mendukung inter-VLAN routing antar keempat VLAN tersebut?
C. Mengkoneksikan trunk uplink dari switch ke salah satu interface Fast Ethernet pada Router dan buat subinterface logis untuk tiap VLAN.
  1. Berdasarkan gambar di bawah, seorang administrator jaringan mencatat bahwa perubahan konfigurasi VLAN pada SW2 tidak dapat diteruskan ke SW3. Bertumpu pada output yang ditunjukkan oleh perintah show vtp status adalah seperti nampak pada gambar berikut. Apa kiranya yang menyebabkan masalah? 
 

B. SW3 dikonfigurasikan pada mode transparent.
  1.  Berdasarkan pada topologi berikut, apa dua kesimpulan yang dapat diperoleh dari informasi yang ada? (Pilih dua.)
 
 D. Defaut gateway dari kedua host diubah menjadi 192.168.3.250/28 agar dapat berkomunikasi atar kedua host.

 E. Diperlukan router yang terkoneksi ke switch agar kedua host dapat saling berkomunikasi.
  1. Berdasarkan pada gambar berikut, beberapa switch saling terkoneksi dengan trunk dalam VTP management domain yang sama. Tiap switch di beri label sesuai dengan mode VTP-nya. Sebuah VLAN baru ditambahkan ke Switch3. VLAN ini tidak nampak pada switch yang lain. Apa alasanya?

 E. Switch mode transparent tidak meneruskan VTP advertisement.


  1.  Berdasarkan kondisi di berikut, switch1 tidak terlibat dalam proses manajemen VTP dengan switch lainnya. Manakah dua alasan yang mungkin untuk kondisi berikut. (Pilih dua)

A. Switch2 dalam mode transparent.
E. Switch1 berada pada domain manajemen yang berbeda.

  1.  Manakah dari pernyataan berikut yang benar berkaitan dengan fitur port security pada Switch?

A. Switch akan menonaktifkan (disable) port yang tidak digunakan.

Diposting oleh di Tidak ada komentar:

Kamis, 05 April 2012

JARKOM CCNA 3


General Use


No.
Perintah Penuh
Perintah Singkat
Maksud Perintah
1
Show running-config
Sh run
Mengetahui konfigurasi yang aktif didalam DRAM (dynamic random acces memory)
2
Show startup-config
Sh start
Mengetahui konfigurasi yang sudah tersimpan didalam NVRAM
3
Show version
Sh ver
Menampilkan informasi tentang versi software yang sedang berjalan lengkap dengan informasi hardware dan device

Routing Related

 

No.
Perintah Penuh
Perintah Singkat
Maksud Perintah
1
Show ip protocols
Sh ip prot
Untuk menampilkan ip protokol
2
Show ip route
Sh ip rout
Menampilkan konfigurasi routing

Interface Related


No.
Perintah Penuh
Perintah Singkat
Maksud Perintah
1
Show interfaces
Sh int
Untuk menampilkan statistic semua interfaces router
2
Shoe ip interfaces brief
Sh ip int bri
Memerinsa status atau kondisi dari tiap-tiap interface yang telah dikonfigurasi
3
Show protocols
Sh prot
Menampilkan status interface baik secara global maupun khusus dari protocol layer 3 yang terkonfigurasi

Connectivity Related


No.
Perintah Penuh
Perintah Singkat
Maksud Perintah
1
Show cdp neightbors
Sh cdp neig
Menunjukan tentang informasi semua piranti cisco tetangga yaitu switch dan router
2
Show session
Sh sess
Memperlihatkan sesi yang ada sekarang
3
Show ssh
Show ssh
Untuk melihat koneksi ssh
4
Ping
Ping
Mengecek koneksi
5
Traceroute
Tr
Untuk menentukan jalur terbaik








 

Konfigurasi pada Router 1


--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#line vty 0 4
Router(config-line)#password telnet
Router(config-line)#transport input telnet
Router(config-line)#login
Router(config-line)#end

Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.1.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 192.168.2.1 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#exit
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#network 192.168.1.0
Router(config-router)#network 192.168.2.0
Router(config-router)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console


Konfigurasi pada router 2


--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]: no


Press RETURN to get started!



Router>ena
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa0/0
Router(config-if)#ip add 192.168.3.1 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#exit
Router(config)#int se2/0
Router(config-if)#ip add 192.168.2.2 255.255.255.0
Router(config-if)#no shut

%LINK-5-CHANGED: Interface Serial2/0, changed state to up

Router(config-if)#exit
Router(config)#
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2/0, changed state to up

Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#network 192.168.2.0
Router(config-router)#network 192.168.3.0
Router(config-router)#exit
Router(config)#exit
Router#
%SYS-5-CONFIG_I: Configured from console by console


Setting IP Pc 1
ip : 192.168.1.2
sm : 255.255.255.0
dg : 192.168.1.1

Setting IP Pc 2
ip : 192.168.3.2
sm : 255.255.255.0
dg : 192.168.3.1

Diposting oleh di Tidak ada komentar:

Senin, 28 November 2011

KONFIGURASI SETTING ROUTER RIP


ROUTER A
Router>ena
Router#conf t
Router(config)#int fa 0/0
Router(config-if)#ip add 205.7.5.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#int fa 1/0
Router(config-if)#ip add 192.5.5.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#int ser 2/0
Router(config-if)#ip add 201.100.11.1 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#router RIP
Router(config-router)#version 2
Router(config-router)#network 205.7.5.0
Router(config-router)#network 192.5.5.0
Router(config-router)#network 201.100.11.0
Router(config-router)#exit
Router(config)#exit
Router#copy run start

ROUTER B
Router>ena
Router#conf t
Router(config)#int ser2/0
Router(config-if)#ip add 201.100.11.2 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#int fa 0/0
Router(config-if)#ip add 219.17.100.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#int ser 3/0
Router(config-if)#ip add 199.6.13.1 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#router RIP
Router(config-router)#version 2
Router(config-router)#network 201.100.11.0
Router(config-router)#network 219.17.100.0
Router(config-router)#network 199.6.13.0
Router(config-router)#exit
Router(config)#exit
Router#copy run start

ROUTER C
Router>ena
Router#conf t
Router(config)#int ser 2/0
Router(config-if)#ip add 199.6.13.2 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#int fa 0/0
Router(config-if)#ip add 223.8.151.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#int ser 3/0
Router(config-if)#ip add 204.204.7.1 255.255.255.0
Router(config-if)#clock rate 64000
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#router RIP
Router(config-router)#version 2
Router(config-router)#network 199.6.13.0
Router(config-router)#network 223.8.151.0
Router(config-router)#network 204.204.7.0
Router(config-router)#exit
Router(config)#exit
Router#copy run start

ROUTER D
Router>ena
Router#conf t
Router(config)#int ser 2/0
Router(config-if)#ip add 204.204.7.2 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#int fa 0/0
Router(config-if)#ip add 210.93.105.1 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#router RIP
Router(config-router)#version 2
Router(config-router)#network 204.204.7.0
Router(config-router)#network 210.93.105.0
Router(config-router)#exit
Router(config)#exit
Router#copy run start

ROUTER E
Router>ena
Router#conf t
Router(config)#int fa 0/0
Router(config-if)#ip add 210.93.105.2 255.255.255.0
Router(config-if)#no shut
Router(config-if)#exit
Router(config)#router RIP
Router(config-router)#version 2
Router(config-router)#network 210.93.105.0
Router(config-router)#exit
Router(config)#exit
Router#copy run start

IP ADDRESS,SUBNET MASK, DAN DEFAULT GATEWAY PADA PC :

PC 0
IP ADDRESS              : 205.7.5.17
SUBNET MASK          : 255.255.255.0
DEFAULT GATEWAY  : 205.7.5.1
PC 1
IP ADDRESS              : 205.7.5.18
SUBNET MASK          : 255.255.255.0
DEFAULT GATEWAY  : 205.7.5.1
PC 2
IP ADDRESS              : 192.5.5.17
SUBNET MASK          : 255.255.255.0
DEFAULT GATEWAY  : 192.5.5.1
PC 3
IP ADDRESS              : 192.5.5.18
SUBNET MASK          : 255.255.255.0
DEFAULT GATEWAY  : 192.5.5.1
PC 4
IP ADDRESS              : 219.17.100.17
SUBNET MASK          : 255.255.255.0
DEFAULT GATEWAY  : 219.17.100.1
PC 5
IP ADDRESS              : 219.17.100.18
SUBNET MASK          : 255.255.255.0
DEFAULT GATEWAY  : 219.17.100.1
PC 6
IP ADDRESS              : 223.8.151.17
SUBNET MASK          : 255.255.255.0
DEFAULT GATEWAY  : 223.8.151.1
PC 7
IP ADDRESS              : 223.8.151.18
SUBNET MASK          : 255.255.255.0
DEFAULT GATEWAY  : 223.8.151.1
PC 8
IP ADDRESS              : 210.93.105.17
SUBNET MASK          : 255.255.255.0
DEFAULT GATEWAY  : 210.93.105.1
PC 9
IP ADDRESS              : 210.93.105.18
SUBNET MASK          : 255.255.255.0
DEFAULT GATEWAY  : 210.93.105.1

Diposting oleh di Tidak ada komentar:
Langganan: Postingan (Atom)